ILY Enterprise CoolCopy 3 User Manual

CD Duplicator  
CoolCopy Series  
User’s Manual  
CoolCopy1AL(CD-Backup)  
CoolCopy 3  
CoolCopy 7  
4.11.6 Auto Verify ...........................................................................22  
4.11.7 Auto Compare ......................................................................22  
4.11.8 Auto Prescan .......................................................................22  
4.11.9 Eject Disc ............................................................................22  
4.11.10 Burn on The Fly ................................................................23  
4.11.11 Burn Mode ........................................................................23  
4.11.12 Button Sound ....................................................................23  
4.11.13 Device Info ....................................................................…24  
4.11.14 System Info .......................................................................24  
4.11.15 Quick Erase ......................................................................25  
4.11.16 Full Erase ..........................................................................25  
4.12 Adv Setup...................................................................................25  
4.12.1 UnderRun Protect ...............................................….............25  
4.12.2 Overburn ...............................................................…...........26  
4.12.3 Read Error Skip............... ..................................…..…... ...26  
4.12.4 Format Hard Disk ....................................................….........26  
4.12.5 Verify HDD ...............................…..................................…...26  
4.12.6 Burn-in.................................................…...…........................27  
4.12.7 Update Firmware..........................................................….....27  
4.12.8 Compare Firmware .......................................................…....28  
4.12.9 H/W Diagnostic ...............................................................…..28  
4.12.10 Load Default ..................................................................….28  
Chapter 5 Troubleshooting .........................................................29  
3
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Chapter 1 Introduction  
1.1 Overview  
People who want to create multiple copies of their CDs usually take a long time to do so. They  
might not have enough CD+RW drives or they might be using their computers for some other  
important tasks. The duplication process noticeably slows down a computer during the burn  
process. Rather than sit at the computer for hours duplicating discs one at a time, it is much more  
efficient to use a CoolCopy CD duplication system.  
The Coolcopy CD Duplicator system is a standalone duplicator and does not need to be  
connected to a computer. It can duplicate discs accurately and quickly. With its multi-function  
LCD panel, Coolcopy CD Duplicator is easy for any user to operate. It is a cost-efficient CD-R  
duplicator for audio, data, and video applications. The simple control panel is designed to provide  
copy mode selection and copy operation.  
1.2 Features  
Standalone IDE to IDE CD Copy controller  
2(Coolcopy1AL(CD-Backup)) / 4(Coolcopy3) / 8(Coolcopy7) / 16(Coolcopy14)  
independent IDE channel  
Self system diagnostics when power on  
Supports Hard Drive image  
Auto format detection  
User friendly interface with message rich LCD display  
Fast copies supports high speed CD-RW writing mode  
Easy operation without software and training are required  
Firmware upgrade via CD-ROM  
1.3 Specification  
Power requirement – voltage:  
Current:  
5VB+/- 5%  
0.5A Max.  
Environment -  
Temperature  
Operating  
Storage  
0˚ C to 70˚ C  
-20˚ C to 85˚ C  
Humidity -  
15% to 90%  
Models:  
Length:  
Width:  
Coolcopy3/coolcopy7  
200 mm  
Dimensions -  
146.2 mm  
Height:  
42 mm  
Connectors -  
40-pin internal IDE connector  
Cable (Optional) - Using ATA-66 (*Cable of length do not use longer than 46cm)  
CD Format -  
CD-ROM (Mode1 & Mode2), CD-ROM/XA (Mode2 form1 & form2), CD-DA,  
Mixed-Mode, Video CD, CD-I, Karaoke CD, Photo CD (Single & Multi-  
session), CD-Extra, HFS, CD Bridge, ISO9660, CD-R, and CD-RW  
Writing mode -  
Auto Detect (DAO, TAO)  
4
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Supported CD-ROM Drives* - EPO, TEAC  
Supported CD-RW Drives* - Plextor, TEAC, Lite-On, Asus, SONY  
Chapter 2 Installation Procedure  
When you receive the Coolcopy CD Duplicator, the package could be packaged in the following  
ways: controller only, whole duplicator without writer installed, and a complete duplication system.  
2.1 Controller only  
1. Before the installation, please prepare the necessary devices as following:  
CD-ROM drive  
CD-R/RW drive  
IDE case (2~10-bay chassis suggested).  
Hard drive and mobile rack (IDE-bus hard drive-Option)  
Switching power supply (300W suggested).  
2. After the preparation as above and make sure that:  
All IDE devices must be in master mode.  
2.2 Whole duplicator without writer installed  
Unpack the package of the duplicators.  
Prepare the CD-R/RW writers according to the recommendation list. Please check with  
the supplier about compatibility issues with unlisted CD-R/RW drives.  
Assemble the duplicator according to your need.  
Make sure that the voltage setting is correct.  
2.3 Completed duplication system  
Take the duplication system out of the package.  
Check the entire unit to see if there are any problems.  
Make sure that the voltage setting is correct.  
The hard drive is optional.  
Hardware Connection of CoolCopy1AL (CD-Backup) without a HDD  
CoolCopy1AL (CD-Backup)  
Power  
CD-RW  
CD-Rom  
5
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Hardware Connection with Hard Drive for Coolcopy3  
Coolcopy 3  
IDE 3
CD-RW  
IDE 2
CD-RW  
IDE 1
CD-RW  
IDE 0
 
CD-Rom/HDD  
Power  
When the system connects with the hard drive, the hard drive must connect on the IDE 0 port  
with the “Master” setting and the CD-ROM must set at “Slave”.  
Hardware Connection without Hard Drive for Coolcopy3  
Coolcopy 3  
IDE 3
 
CD-RW  
IDE 2
 
CD-RW  
IDE 1
 
CD-RW  
IDE 0
 
CD-Rom  
Power  
6
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Hardware Connection with Hard Drive for Coolcopy7  
Coolcopy 7  
IDE 4  
IDE 3  
IDE 2  
CD-RW  
CD-RW  
CD-RW  
IDE 1
 
CD-Rom/HDD  
IDE 8  
IDE 7  
IDE 6  
IDE 5  
CD-RW  
CD-RW  
CD-RW  
CD-RW  
Power  
7
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
When the system has a hard drive connected, the hard drive must connect on IDE 0 port with  
“Master” setting and the CD-ROM must set at “Slave.”  
Hardware Connection without Hard Drive for Coolcopy7  
Coolcopy 7  
IDE 4  
IDE 3  
IDE 2  
IDE 1  
IDE 8  
IDE 7  
IDE 6  
IDE 5  
CD-RW  
CD-RW  
CD-RW  
CD-Rom  
CD-RW  
CD-RW  
CD-RW  
CD-RW  
Power  
8
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Chapter 3 Key Functions and Operating Instruction  
1. LCD Display Panel: Display main functions and all messages.  
2. Scroll up through menus or functions.  
3. Scroll down through menus or functions.  
4. Execute the function which you select.  
5. Cancel the function which you select.  
After turning the power on, the Coolcopy CD Duplicator will execute a self test for a few seconds.  
After the self testing procedure runs, the LCD will show:  
1.  
2.  
Coolcopy3:  
Coolcopy7:  
CD Duplicator  
1-3 ver: 1.10B  
CD Duplicator  
1-7 ver: 1.10T  
Initialize SDRAM.....  
3.  
4.  
Detect Drives.....  
1. Copy  
Two main operation procedures  
If you install a 3.5” hard disc, the operation procedures is as follows:  
1. With hard drive installed  
Once duplicator detects a hard disc, it will ask if you want to format or not. A 10GB hard  
disc can be divided into 10 partitions.  
Use the Select Source to set the hard drive as the target source.  
Then select which partition to store the data in function 9 “Image.”  
If there is no data stored in partition, insert a source CD into CD-ROM and use function 9-  
01 Load to transmit data from CD into selected partition by pressing ENT. Different data  
can be stored in different partitions.  
Switch to the Copy function by pressing the arrow button. Insert blank CD-R or CDRW  
discs into the CD writers. Press “ENT” button to start copying.  
9
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
When a Copy completes, the passed (correctly copied) CD discs will be ejected  
automatically. The default is to eject automatically, but this can be changed.  
Failed discs will remain in writers. The default setting is keeping failed discs in the writers,  
but this can be changed. Press the buttons on the drivers to take the failed CDs.  
During operation do not press any button, interruption will harm the device. CDs will be  
damaged.  
2. Without a hard drive installed  
If you don’t install a 3.5” hard disc, the operation procedures will be as follows:  
Insert the master disc to CD-ROM.  
Switch to the Copy function by pressing arrow button. Insert blank CD-R or CDRW disc  
into all the CD writers. Press “ENT” button to start.  
When Copy completes, the passed CDs will eject automatically. The default is to eject  
automatically, but this can be changed.  
Failed CDs will remain in the writers. The default setting is that failed CDs stay in the  
writers, but you can change the setting. You need to press the “eject” buttons on the  
writers to take the failed CDs.  
ATA-66 Cable Layout:  
Please identify two different kinds of cable before the hardware installation.  
Chapter 4 Function  
4.1 Copy  
Use this function to copy data from a source CD directly onto blank CD discs. Before copying  
make sure that the source CD is insertd into CD-ROM. If you have a HDD, make sure there is  
data in your HDD partition. If you are not sure about the success of your duplication job, you can  
use function 2, Test, to simulate the copying process first.  
Select function 1. Put a source CD into CD-ROM and blank CD disks into CD writers. CD  
rewriteable discs containing old data are usable, too.  
Copying-24X 0%  
650.0MB 74:00  
LCD will show the process of copying  
information as follows:  
3. Test & Copy  
OK: 03  
When copying is completed, the LCD will display as  
1. Copy  
OK: 03  
the following information:  
Discs correctly copied will be ejected automatically  
10  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
and failed ones will remain in the writers.  
4.2 Test  
Function 2 Test will simulate the copying process. When the simulation completes, the discs will  
remain blank.  
Press “ENT” button to start the disc simulation  
or press “ESC” to exit.  
2. Test  
If you use CD rewriteable discs that contains data, the old  
Data will be quickly erased before before simulation begins:  
LCD will show the following testing  
Testing-24X 0%  
Information:  
.
650.0MB 74:00  
When the process is finished, the LCD will  
show the following message:  
2. Test  
OK: 03  
Stopping the test halfway does not affect the CD discs. However, if the CD rewriteable discs  
contain important data, the information might be erased.  
4.3 Test&Copy  
Function 3 Test & Copy is to test first and then actually copy.  
Select Function 3. Put a source CD into CD-ROM  
3.Test & Copy  
And blank CD discs into writers.  
Press ENT to start simulation. LCD will show the  
Information as follows:  
Testing-24X 0%  
650
.
0MB 74
:
00  
After the tests finishes, actual copying will begin  
as follows:  
Copying-24X 0%  
650.0MB 74:00  
When the entire process finishes, the LCD will  
show the information as follows:  
4. Test & Copy  
OK: 03  
4.4 Verify  
Function 4 Verify is to examine if the target CDs can be read correctly after copying.  
11  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Press “ENT” button to verify. LCD will shows as  
follows:  
4. Verify  
LCD will show verification information as  
follows:  
Verify--24X 0%  
650.0MB 74:00  
When the verification process is finished, the LCD  
will display the result as follows:  
4. Verify  
OK: 03  
4.5 Compare  
Function 5 Compare is to make a comparison between the source and the target CDs after  
copying.  
Select Function 5. Put the source CD into CD-ROM  
and the target CDs into CD writers.  
5. Compare  
Press ENT to compare. LCD will show the  
comparison information as follows:  
Compare-24X 0%  
650.0MB 74:00  
When comparison completes, LCD will show  
as follows:  
Compare OK: 3  
Fail: 0 Diff: 0  
Press “ENT” button to see the details of  
source 1. If comparison is identical, LCD  
will show the message as follows:  
Src: 01 CD-ROM  
Total: 650.0MB  
If the compare result is identical, the LCD will  
show as follows:  
Src: 02 CD-RW  
Identical  
If comparison fails, LCD will show failure.  
Compare OK: 2  
Fail: 1 Diff: 0  
Src: 01 CD-ROM  
Total: 0 Bytes  
Press “ENT” button to see comparison  
information.  
If the comparison fails, the LCD will show  
failure. By pressing ENT twice, LCD will show  
the contents of source 1 and those of source 2  
do not match as follows:  
Src: 02 CD-RW  
TOC not match  
12  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
4.6 Prescan  
Use the prescan function to scan if the source CD can be read correctly and also to test the  
reading speed.  
Select function 6. Put the source CD  
into CD-ROM.  
6. Prescan  
Press ENT to prescan, LCD will show the  
scanning information as follows:  
Scaning-24X 0%  
650.0MB 74:00  
If the master of the disc can read correctly,  
the source CD has no problems. LCD  
will show the following:  
PreScan OK!  
PreScan Fail!  
If the master disc cannot be read correctly,  
the LCD will show the message as follows:  
4.7 Disc Info  
Function 7, Disc Info, shows the basic information of the source CD.  
Select Function 7. Insert source CD into CD-ROM.  
7. Disc Info  
Press the “ENT” button to show the disc information.  
The LCD will show the total sessions and  
tracks on the master disc.  
Total 02 Sessions  
Total 10 Tracks  
Press the “ENT” button again, the LCD will show  
the total time and capacity on the master disc  
Total: 74:00  
Total: 650 MB  
Press the “ENT” button again and use arrow button  
to select the session, LCD will show the  
information contained in the session.  
Session 01  
Track 01 - 09  
Press the “ENT” button again and use arrow button  
to select the track. The LCD will then show what  
information is contained on the track.  
Track 01  
AUDIO 03:54  
4.8 Select Source  
Function 8 Select Source will let you select the data on CD-ROM, CD writers or HDD as the  
source from which you intend to copy.  
13  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
8. Select Source  
Select function 8.  
Press ENT and then use arrow button to select the  
source.  
Src: CD-ROM  
01 IDE0 Slave  
After selecting source, press ENT and LCD will  
show the following:  
CD-ROM selected!  
Note: Suppose you select HDD as the source and try to copy from one of its partitions, but the  
partition contains no data. An error message will then appear on your LCD. From here, you can  
switch to another partition that contains no data or use function 9 Image to load the data into the  
chosen partition first.  
4.9 Image  
Function 9, Image, is only valid when you have installed a hard drive.  
Select function 9. Press ENT.  
9. Image  
4.9.1 Load  
Insert the master CD disc into the CD-ROM or any one of the CD writers, the duplicator  
will detect and analyze the master CD.  
Here the Load function will allow you to load data  
from CD-ROM or any CD writer into the current  
partition of the hard disc. P:A means Partition A.  
9-01.Image P: A  
Load  
Press ENT to load. LCD will then show the loading  
information.  
Load- A -24X 0%  
650.0MB 74:00  
When the image has successfully loaded, the LCD  
will show the following:  
Image load OK  
If there is an image file existing in current partition,  
the system will ask whether you want to overwrite.  
Use arrow button to make a “Yes” or “No” selection.  
Image Exists  
Overwrite?Yes  
4.9.2 Delete Image  
If you want to empty an image file stored in a particular partition, you can use the function Delete  
Image to do so.  
9-02. Image P: A  
Delete Image  
Select function by pressing arrow.  
Delete Image in  
Partition A?Yes  
The system will ask if you are sure you want to delete.  
Use arrow button to make “Yes” or “No” selection.  
14  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
When the image is successfully deleted from the  
hard drive, the LCD will show as follows:  
Partition A:  
Image is deleted  
4.9.3 Imae Info  
This function shows the basic information of an image file stored in a particuar partition.  
Press ENTto show the isc information.  
9-03.Image P: A  
Image Info  
The LCD will show the total sessions and tracks  
in the partition.  
Total 01 Sessions  
Total 01 Tracks  
Press ENT again. The LCD will show  
the total time and capacity in the hard drive of  
partition.  
Total: 74:00  
Total
:
650 MB  
Press ENT again and use arrow button  
to select the session. LCD will show the information in  
the session.  
Session 01  
Track 01 - 01  
Press ENT again and use arrow button  
to select the track. LCD will show track  
information.  
Track 01  
DATA 650.0MB  
4.9.4 Compare Image  
Use this function to compare the contents of the source CD and those of the image file in the  
partition. First select the funcion by pressing the arrow.  
9-04. Image P: A  
Compare Image  
Pres ENT and LCD willshow the omparison  
information as follows:  
LCD will show the following screen:  
Comp-A-24X 0%  
650.0MB 74:00  
When the process is finished, the LCD will display  
the following message:  
Compare OK: 1  
Fail
:
0 Diff
:
0  
Press ENT to view the comparison details.  
Src: 01 CD-ROM  
Total: 650.0MB  
Tgt: 00 HDD P:A  
Identical  
If the comparison is identical, the LCD will  
show the following message:  
15  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
If comparison fails, LCD will show the number of discs  
failed and succeeded.  
Compare OK: 0  
Fail: 1 Diff: 0  
Press ENT to see the comparison  
information.  
Src: 01 CD-ROM  
Total: 0 Bytes  
If the comparison fails, the LCD will show  
the reason as follows:  
Src: 02 CD-RW  
TOC not match  
4.9.5 Select Partition  
This function is to select a partition in the hard disc.  
Press ENT button to change the setting.  
9-05.Image P: A  
Select Image  
After installing a hard disc, duplicator will format it automatically. Each partition occupies 1GB.  
The number of partitions is dependent on the hard disc’s capacity. The partitions are  
alphabetically arranged.  
Use arrow button to select which partition will  
be worked.  
Select Working  
Partition - A  
When the partition is set, the LCD will show the  
following:  
Set Partition to  
A
4.9.6 Select Src Drive  
This function selects CD-ROM or any CD writer as the source from which you can load data into  
a particular partition as an image file.  
Press ENT and arrow button to select  
the source.  
9-06. Image P: A  
Image Src Drive  
Then use arrow button to select the disc as the master  
Select Img Src:  
source.  
01 IDE0 CD-ROM  
After selecting the source, press ENT.  
LCD will show the source information the following info:  
Load image from  
Drive ID-01  
4.10 Edit Track  
16  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Function 10, Edit Track, allows you to edit a collection of favorite songs from CDs. You’re able to  
collect different tracks or songs on a number of CDs and merge them onto a single CD. This  
process can be divided up into four parts: CD to CD, CD to HDD, Play Audio Track and Close  
Session.  
Press ENT and use the arrow button to select function 10.  
10. Edit Track  
4.10.1 CD to CD Edit  
Select “CD to CD Edit” to select one or more tracks from CD-ROM and then copy onto blank CD-  
R/RWs.  
Press ENT to change setting.  
10-01. Edit Track  
CD to CD Edit  
Follow the LCD to select the track that you want  
to edit.  
Select Track:  
1/10  
03:25  
Press ENT to select the track. After the  
track is selected, the “+” will appear beside 1/10 as shown.  
Pressing ENT again will cancel the track.  
Select Track:  
+1/10  
03:25  
When the track selection is made, use arrow button  
to move to the “End” manual.  
Select Track:  
End 1Trk03:25  
Press ENT to finish the disc editing. Use arrow button  
to make a selection.  
End edit disc  
and burn?Yes  
LCD will show copying information as follows:  
Copying- 24X Edit  
1/10 - > 1/1  
When copying ends, the LCD will show the  
“Burn Complete!” message:  
Burn Complete!  
OK: 03  
System will ask if you want to continue editing. Use the arrow  
button to make a selection.  
Continue edit  
next Disc?Yes  
If “Yes” is selected, the source disc will be  
automatically ejected. Insert another disc.  
Insert next disc  
Follow the steps to select the track that you want  
to edit. Then press ENT.  
Select Track:  
+2/10 04:25  
When the track selection is made, use arrow button  
to move to the “End” manual.  
Select Track:  
End 2Trk07:50  
End edit disc  
and burn?Yes  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Press ENT button to finish the disc edition.  
Use the arrow button to make a selection.  
17  
Copying- 24X Edit  
1/10 - > 2/2  
LCD will show copying information as follows:  
The 2/2 means the second track of all tracks you have  
selected. So far you have selected two tracks from two  
different CDs.  
Burn Complete!  
OK: 03  
When copying is finished, the LCD will show the  
following message:  
The system will ask if you want to continue editing. Use arrow  
button to select “no” then press  
ENT.  
Continue edit  
next Disc?No  
The system will ask to close the disc session.  
Use arrow button to make “Yes” or “No”  
selection.  
Close all disc’s  
session? Yes  
LCD will show the following screen  
when you are closing the session:  
Closing Session  
Please wait---  
4.10.2 CD to HDD  
This function lets you select one or more tracks from CD-ROM and then copy the source into a  
certain HDD partition.  
10-02. Edit Track  
CD to HDD Edit  
Press ENT to enter the setting.  
Follow the LCD to select the track that you want  
Select Track:  
to edit. Here 1/10 means the number one of 10 tracks  
1/10  
03:25  
and 3:25 means the playing time.  
Press ENT button to select the track. After the  
track is selected, the “+” will appear. Pressing  
ENT again will cancel the track.  
Select Track:  
+1/10  
03:25  
Select Track:  
End 1Trk03:25  
When track selection is made, use arrow button to  
move to the “End” manual.  
Press ENT to finish the disc editing. Use arrow  
button to make a selection.  
End edit disc  
and burn?Yes  
The source will be loaded to hard drive. LCD  
will show the loading information as follows:  
Load- P0 -24X Edit  
1/10 - > 1/1  
When the “Image Load” is finished, the LCD will  
show the message as follows:  
Image load OK  
The system will ask if you want to continue editing. Use the arrow  
18  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Continue edit  
next Disc?Yes  
button to make “Yes” or “No” selection.  
16  
Insert next disc  
If “Yes” is selected, the source disc will be automatically  
ejected. Insert another disc.  
Select Track:  
+2/10 04:25  
Follow the steps to select the track that you want  
to edit. Then press ENT button.  
Select Track:  
End 2Trk07:50  
When the track selection is made, use arrow button  
to move to the “End” manual.  
Press ENT button to finish disc editing. Use arrow button  
to make a selection.  
End edit disc  
and burn?Yes  
The track will be loaded as an image file onto hard drive.  
LCD will the following information.  
Load- P0 -24X Edit  
1/10 - > 2/2  
When loading is finished, the LCD will  
show the message as follows:  
Image load OK  
System will ask you whether you want to continue editing.  
Use arrow button to make a selection. Select  
“No” to go next step.  
Continue edit  
next Disc?No  
System will ask you if you want to burn from the HDD onto  
CD-R/RW or move into a partition. Selecting “Burn” will  
start the process.  
Burn or Move to  
Partition?Burn  
LCD will show the copying information as follows:  
Copy- P0 -24X 0%  
1/2 Trk03:25  
When burning is finished, the LCD will show  
the message as follows:  
Burn Complete !  
OK: 03  
Selecting “Move” will move the data from the hard  
drive template to a certain partition.  
Burn or Move to  
partition? Move  
Select the partition that the data will move into by  
pressing the arrow.  
Select Partition  
A
LCD will show the moving information as follows:  
Moving to P: A  
0%  
When moving is finished, the LCD will show  
the message as follows:  
Moving to P: A  
OK!  
If the chosen partition contains image data,  
system will ask to overwrite it. Select “No” to  
19  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Image Exists  
Overwrite?Yes  
keep the data image or “Yes” to overwrite it.  
LCD will show the moving information as follows:  
Moving to P: A  
0%  
When moving is finished, the LCD will show the  
message as follows:  
Moving to P: A  
OK!  
4.10.3 Play Audio Track  
This function allows your machine to be utilized as a music player. Plug in an AV terminal in the  
audio port on the back of the device.  
Press ESC and the arrow button to enter the play audio  
10-03. Edit Track  
function.  
Play Audio Track  
Use arrow button to select track you  
are going to play.  
Select Track:  
1/10 03:25  
Press ENT and LCD will display the playing information  
as follows:  
Playing Track-1  
00:00 / 03:25  
4.10.4 Close Session  
Select “Close Session” will close the disc and restrict data writing. This function allows discs to be  
read on any normal player.  
Press ESC and arrow to select the function.  
10-04. Edit Track  
Close Session  
Press ENT, the system will ask whether you want to  
Close all disc’s  
close. After this step, data cannot be written onto the disc.  
session? Yes  
Closing Session  
LCD will show the message as follows:  
Please wait---  
When closing session is finished, the LCD will  
show the following message:  
Closing  
Complete  
4.11 Setup  
This function allows you to change default settings. It is suggested that you use default setting for  
optimal performance.  
Press ENT button to enter the Setup function.  
11. Setup  
20  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
4.11.1 Language (optional)  
Here are the available languages on the LCD: English, Traditional Chinese, Simplified Chinese  
and Japanese.  
11-01. Setup  
Language  
Press ENT to change the setting and ESC to  
exit.  
4.11.2 Burn Speed  
This setting controls the burning speed of CD writers. Default setting is “Auto,”  
which would use the highest available writing speed of the writer.  
Press ENT to enter the setting.  
11-02. Setup  
Burn Speed  
Use arrow button to change the burning  
speed then press ENT.  
Burn Speed  
24X  
4.11.3 Read Speed  
This function lets you control the reading speeds of target CDs.  
Press ENT to enter the setting.  
11-03. Setup  
Read Speed  
Use arrow button to change the reading  
speed then press ENT. The default is maximum but other  
choices are 32X, 16X and 8X.  
Read Speed  
32X  
4.11.4 Auto Start Drive  
This function automatically tests or copies discs once you put the blanks discs into the writers.  
Press ENT button to enter Auto Start Drive.  
11-04. Setup  
Auto Start  
Use arrow button to change the number or  
“Off” setting. Then press ENT or ESC to  
go back 11-04 menu.  
Auto Start  
Drive  
4.11.5 Start up menu  
This setting lets you select any one of the functions, except Adv Setup, as the first item to appear  
on the menu when you turn on your device.  
11-05. Setup  
Press ESC button to enter Startup Menu and  
Startup Menu  
ENT to enter the following figure:  
Use the arrow button to select other function settings, which will  
Startup Menu  
1.Copy  
be the first setting to appear when the device is turned on.  
Then press ENT.  
21  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
4.11.6 Auto Verify  
This setting allows you to automatically verify if target CDs can be read after copying.  
11-06. Setup  
Auto Verify  
Press ENT button to enter the following figure:  
Use arrow button to change the “On” or “Off”  
setting. Then press ENT or press ESC to go  
return to 11-06 menu.  
Auto Verify  
Off  
4.11.7 Auto Compare  
This setting allows you to automatically compare the source CD and target CDs after copying.  
Press ESC button and arrow to enter setting.  
11-07. Setup  
Auto Compare  
Use arrow button to change “On” or “Off”  
setting. Then press ENT to go  
back 11-07 menu  
Auto Compare  
Off  
4.11.8 Auto Prescan  
This setting allows you to automatically scan if the source CD can be read correctly and also tests  
the reading speed.  
Press ENT button to enter Auto Prescan.  
11-08. Setup  
Auto Prescan  
Use arrow button to change “On” or “Off” Setting.  
Then press ENT or press ESC to return to 11-08 menu.  
Auto Prescan  
Off  
4.11.9 Eject Disc  
Eject disc allows three choices: Eject Good Only, Eject All Disc and Do Not Eject.  
11-09. Setup  
Eject Disc  
Press ENT button to enter the following figure:  
Use arrow button to select Eject Good Only.  
Then press ENT or press ESC to return to 11-  
09 menu.  
Eject Disc  
Eject Good  
22  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Use arrow button to select Eject All Disc,  
then press ENT or press ESC to return to 11-  
09 menu.  
Eject Disc  
Eject All Disc  
Use arrow button to select Do Not Eject. Then press  
ENT or press ESC to go back 11-09 menu.  
Eject Disc  
Do Not Eject  
4.11.10 Burn on the Fly  
This setting lets you controls the burning methods. When the setting is “On”, the data will copy  
directly from source drive to the target drives. When the setting is “Off”, the data will load into a  
partition of the hard drive first. Then, the copying will be completed.  
Press ENT button to enter Burn On The Fly.  
11-10. Setup  
Burn On The Fly  
Use arrow button to change the On or Off  
Setting. Then press ENT or press ESC to return to  
Burn On The Fly  
On  
The 11-10 menu.  
If the system does not connect with hard drive,  
the LCD will show the following message.  
There is no HDD !  
4.11.11 Burn Mode  
This setting lets you control the burning methods. There are two modes: Disc At Once (DAO) or  
Track At Once (TAO). Default setting is DAO. Some CD writers may support different writing  
methods. If the method selected is not supported, duplicator will automatically switch to the other  
one.  
.
Press ENT button to enter Burn Mode.  
11-11. Setup  
Burn Mode  
Use arrow button to change TAO or DAO  
mode setting. Then press ENT or press ESC  
to return to 11-11 menu.  
Burn Mode  
DAO  
4.11.12 Button Sound  
This setting allows you to control the sound when you press it.  
11-12. Setup  
Button Sound  
Press ENT button to enter Button Sound.  
Use arrow button to change On or Off  
setting. Then press ENT or press ESC to return to  
11-12 menu.  
Button Sound  
On  
23  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
4.11.13 Device Info  
This function shows the information of the CD-ROM and any CD writer you have installed.  
11-13. Setup  
Device Info  
Press ENT button to enter the device information.  
00 IDE0 Master  
Use arrow button to select the device or press  
ESC to go back 11-13 menu.  
CD-ROMꢀꢁꢀTEAC  
Press ENT button to see the device information  
and ESC to return to the 11-13 menu.  
CD-540E  
3.0A  
Use arrow button to select another device or  
press ESC to return to the 11-13 menu.  
01 IDE1 Master  
CD-RW
ꢀꢁꢀ
PLEXTOR  
Press ENT button to see the device information  
and ESC to return to the 11-13 menu.  
CD-R PX-W2410A  
1.01  
Use arrow button to select another device or  
press ESC to return to the 11-13 menu.  
02 IDE2 Master  
CD-RW
ꢀꢁꢀ
PLEXTOR  
Press ENT button to see the device information  
and ESC to return to the 11-13 menu.  
CD-R PX-W2410A  
1.01  
Use arrow button to select another device or  
press ESC to return to the 11-13 menu.  
03 IDE2 Master  
CD-RW :PLEXTOR  
Press ENT to see the information and ESC  
to return to the 11-13 menu.  
CD-R PX-W2410A  
1.01  
4.11.14 System Info  
This function shows the information of the system.  
Press ENT button to enter the System Info and see  
the next information. Press ESC to exit.  
11-14. Setup  
System Info  
The LCD shows  
Coolcopy3 as follows:  
CD Duplicator  
1-3 ver: 1.10B  
SST: 39SF020  
2001 / 11 / 16  
The LCD shows  
Coolcopy7 as follows:  
CD Duplicator  
1-7 ver: 1.10T  
WINBOND: W49F002U  
2001 / 11 / 16  
24  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
11-15. Setup  
Quick Erase  
4.11.15 Quick Erase  
This function will quickly erase the data on the disc.  
Press ENT button to enter the Quick Erase  
and ESC to exit.  
Use arrow button to confirm whether you want to erase  
the data. Select the “Yes” or “No” setting. Then press  
ENT or press ESC to return to 11-15 menu.  
All data will be  
lost, erase? Yes  
LCD will show the information as follows:  
Erasing disc  
00:24 (Quick)  
When erasing disc function is finished, the LCD will  
display as follows:  
Quick Erase  
OK:01 Fail:00  
4.11.16 Full Erase  
This function is to completely erase the data on the CD rewriteable discs.  
Press ENT to enter the Full Erase.  
11-16. Setup  
Full Erase  
Use arrow button to select “Yes” or “No.”  
All data will be  
Then press ENT or ESC to return to 11-16 menu.  
lost, erase? Yes  
LCD will show the information as follows:  
Erasing disc  
03:24 (Full)  
When finished, the LCD will show the message the  
following message:  
Full Erase  
OK:01 Fail:00  
4.12 Adv Setup  
This function allows you to change the system configuration. Changes should be made only when  
you are fully familiar with the function. To enter the function, please press “ESC” button for 2  
seconds.  
4.12.1 UnderRun Protect  
This function lets you control Buffer Under Run Protection settings, such as Burn Proof,  
SafeBurn, JustLink, Seamless Link, etc.  
12-01. Adv Setup  
Press ENT button to enter “UnderRun Protect.  
UnderRun Protect  
25  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Use arrow button to change the  
setting. Then press ENT or ESC to return to the  
12-01 menu.  
UnderRun Protect  
On  
4.12.2 Overburn  
This setting lets you decide whether to copy beyond the limit of the CD or not.  
12-02. Adv Setup  
Overburn  
Press ENT button to enter Overburn.  
Use arrow button to change the  
setting. Then press ENT or ESC to return to the  
12-02 menu.  
Overburn  
On  
4.12.3 Read Error Skip  
This function allows you to neglect any error that occurs during copying. You can use this function  
to copy some defective CDs.  
12-03. Adv Setup  
Read Error Skip  
Press ENT button to enter Read Error Skip.  
Use arrow button to change the  
setting. Then press ENT or ESC to go  
back to the 12-03 menu.  
Read Error Skip  
Off  
4.12.4 Format Hard Disk  
This function allows you to partition the hard drive.  
Press ENT button to enter Format HDD.  
12-04. Adv Setup  
Format HDD  
Use arrow button to change the  
setting. Then press ENT or ESC to go  
back to the 12-04 menu.  
All data will be  
lost, format? Yes  
If the system does not connect with hard drive,  
the LCD will show the message as follows:  
There is no HDD!  
4.12.5 Verify HDD  
This function is to verify if the hard disc or any of its partitions are working well.  
Press ENT to enter Verify HDD.  
12-05. Adv Setup  
Verify HDD  
26  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Use arrow button to change setting to Disk.  
Then press ENT or ESC to go back to the 12-  
05 menu.  
Verify Disk or  
Partition? Disk  
Use arrow button to change setting to Parti.  
Then, press ENT or ESC to go back to the 12-05 menu.  
Verify Disk or  
Partition? Parti  
4.12.6 Burn-in  
This function is a burn-in test, which will simulate the copying process multiple times. After each  
cycle, the CDs on the CD writers will be ejected automatically and re-inserted again for  
continuous testing.  
Press “ENT” button to enter “Burn-in” and  
12-06. Adv Setup  
Burn-in  
“ESC” to exit  
The data will not be written on the blank  
CD discs and the discs will remain blank  
after the test.  
Burn-in  
Test  
.
Using arrow button to change  
“RunContinuous”, “1~10”, “10~100”,  
“100~1000” setting. Press “ENT” or “ESC”  
button to go back 12-06 menu.  
Sel burn-in num:  
Run Continuous  
The system will repeat to erase and write  
on the CD-RW discs. Only CD+RW discs can  
be rewritten.  
Burn-in  
Erase&Copy  
Using arrow button to change  
Sel burn-in num:  
Run Continuous  
“RunContinuous”, “1~10”, “10~100”,  
“100~1000” setting. Press “ENT” or “ESC”  
button to go back 12-06 menu.  
4.12.7 Update Firmware  
This function will update your firmware to the latest version. Insert the CD disc which contains the  
latest firmware data (firmware CD disc) into the CD-ROM drive and the duplicator will find the  
data and update its firmware automatically. During updating, do not turn off the power of machine  
because the update will not be finished until machine resets itself.  
The Update Firmware function updates firmware to the latest version.  
2. Unzip the firmware you have and write the file “cdxxx.bin” into the root directory of a blank  
CD-R or CD-RW disc. You have to close the session of the CD. If the same CD disc still has  
capacity to add more data, it can be used to store newer versions of firmware. When updating the  
firmware program from the CD, only the one from last session will be used. Versions from  
previous sessions will be ignored.  
Select source drive to CD-ROM first! Then  
12-07. Adv Setup  
Update Firmware  
press “ENT” button to enter “UpdateFirmware”  
and “ESC” to exit.  
27  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
System will search the new firmware from the  
CD and the LCD will show the process as left.  
When find the new firmware, just press “ENT”  
button. The system will update it.  
Searching F/W---  
XXX/XXXXX  
4.12.8 Compare Firmware  
This function will help you compare your current control firmware version and the updated version  
in your firmware disc that you insert into the CD-ROM.  
Press “ENT” button to enter “Compare Firmware”  
12-08. Adv Setup  
and “ESC” to exit.  
.
Compare Firmware  
4.12.9 H/W Diagnostic  
This function will detect which types of devices are connected with the control. The LCD will show  
the hardware information.  
Press the ENT button to enter “H/W Diagnostic”  
and “ESC” to exit.  
12-09. Adv Setup  
H/W Diagnostic  
LCD will ask user to do the button test. Following  
the LCD instruction test each function button.  
ꢀꢀꢀꢀꢀEnter ESC  
Hold ESC to exit  
After the button function testing, the system will self-test SDRAM, the hardware connecting test,  
and flash test. Every testing process will be shown on the LCD. It just takes a few minutes to get  
the results of hardware diagnostics. It is an easy way to know if the system works properly.  
When testing is finished, the LCD will show the  
“Test finished” message. Press “ESC” button to  
go back 12-09 menu.  
Test finished  
4.12.10 Load Default  
This function will reset whole previous setting back to factory’s default setting. Different settings  
will cause duplicator to react differently.  
12-10. Adv Setup  
Press “ENT” button to enter “Load Default” and  
Load Default  
“ESC” to exit.  
Use the arrow button to change settings. When  
Load Default  
Config? Yes  
“Yes” is selected, the duplicator will return to  
factory’s default setting.  
Load Default  
OK  
The LCD message will show that the setting has  
been changed by with the follow message:  
28  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
Chapter 5 Trouble Shooting  
1. No display on LCD or the unit does not operate when power on.  
Please check the connection of power cable and that the power  
outlet is normal.  
Turn off the power of machine, open the case of duplicator, and check if  
there are any problems with the power cable.  
2. LCD shows the Error message.  
During operation like Copy, Test, Compare and Verify, you may press ESC  
button to abort the operation. An Error message will be shown no the LCD.  
Some CD writers will cause the duplicator to reset and you have  
to re-start the power to get the duplicator to function properly.  
A failed reading may cause an error message to show on the LCD display.  
Change the master CD and try again.  
During operation, if a read error, buffer under run or writing error occurs, the  
LCD will show error message like: Pass xx, failed xx.  
If there is no device connected and detected by duplicator during power-on,  
the duplicator will show an error message on the LCD before entering the main menu.  
3. CD-ROM can not read disc and shows error message.  
Check the format of master CD or master CD itself for damage.  
Use any of the CD-Writers to read the master. If it works, the CD-ROM may be  
defective or not compatible with CD-ROM.  
4. Buttons do not function.  
May be still busy on task.  
Button malfunction.  
Faulty board.  
5. Copy completed but CD-R disc is not readable / executable?  
Use the compare function to check.  
Change another CD-ROM drive to test.  
6. The failure rate is high.  
Lower the speed of the CD-Writers and try again.  
Quality of blank disc is poor.  
Check for latest firmware version.  
Check the CD-Writer maximum writing speed. If you want to copy at 24X writing  
process or higher, please copy to hard drive first and then to CD.  
7. Can not boot-up or failure to upgrade firmware.  
Contact your dealer to solve the problem. Please note that ay be charged  
for this.  
Check to see if the BIOS program is correct since customers often download  
the wrong program or simply write the zipped file to CD when it should be first  
unzipped before writing.  
A failed upgrade might cause a failed boot. This can only be solver by returning  
the control board to agent or factory directly. It is not necessary to return  
whole system under failed upgrade.  
29  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  
8. Can not find the “12. Adv Setup” function.  
Press “ESC” button for 2 seconds to enter the “Adv Setup”.  
9. To cancel the duplicator working process.  
Press “ESC” button for 2 seconds to cancel any “Copy”, “Test”, or “Verify” etc.  
function while the job is in progress.  
30  
Copyright ©2005 by ILY Enterprise Inc.  
All Rights Reserved.  

National Instruments DN V210 User Manual
LG Electronics P880 User Manual
Kingston Technology SecureTraveler User Manual
HTC KII0160 User Manual
Hitachi Deskstar HDS721075DLE630 User Manual
Hamilton Beach 42884 User Manual
DeLonghi DCM900 User Manual
Casio CTK 4200 User Manual
Bunn Coffeemaker CWTF35 User Manual
Anaheim CLCI2000 User Manual